Upper/Lower Supersets: A 45-Minute Upper Day in a Busy Gym
You have 45 minutes, including your warm-up, and somebody is already using the cable row. Keep your first press, do your vertical pull in straight sets, then pair two exercises you can do on the same incline bench. Finish with one cable station if it’s free. You can run this version of Upper A without asking anyone to keep a second machine open for you.
Jump to the 45-minute workout ↓

What changes in the 45-minute version?
The THG four-day upper/lower plan gives Upper A a pressing priority and Upper B a pulling priority. A normal Upper A has 16 working sets. This example keeps both working sets of each press and pull. It trims one set each from curls and pushdowns, for 14 working sets. Use your regular Upper B when its turn comes.
| Upper A exercise | Usual session | 45-minute session |
|---|---|---|
| Flat bench press | 2 × 5–8 | Same, straight sets |
| Lat pulldown | 2 × 6–8 | Same, straight sets |
| Incline dumbbell press | 2 × 8–10 | A1 on an incline bench |
| Chest-supported row | 2 × 8–10 | A2 with dumbbells on that bench, 2 × 8–10 |
| Cable lateral raise | 2 × 12–15 | 2 × 12–15, or use dumbbells |
| Cable curl and triceps pushdown | 3 × 10–15 each | B1 and B2, 2 × 10–15 each |
Run the session one station at a time
These times are estimates, including setup and equipment changes. The clock starts when you begin warming up. If the gym costs you five minutes of waiting, take them out of the accessory block.
- 0–13 minutes · Bench. Set up, take the warm-up sets you need, then perform your two working sets. Aim to finish with 1–3 good reps in reserve. Allow roughly 2–3 minutes between working sets, longer if you need it. A machine chest press is an option if the rack is occupied. Log it as its own exercise. Sharing the bar with another lifter? Use the partner plate calculator to work out what to add on each side.
- 13–20 minutes · Pulldown. Take two sets at 1–2 reps in reserve. Allow around two minutes between them. A familiar assisted pull-up works if the pulldown is busy. Release the station when you finish.
- 20–31 minutes · A1 incline press + A2 chest-supported dumbbell row. Use a stable incline bench and loads you can set down under control. Press, put the weights down, then face the pad for the row. Take about 20–40 seconds to change position and load. After the row, rest about 90–120 seconds. Repeat once. Depending on set length, each muscle gets roughly 2½–3½ minutes before its next set. If the bench angle makes the row awkward, do straight sets and use your usual row when it opens.
- 31–36 minutes · Lateral raises. Use the cable if available or a pair of light dumbbells for both sets. Keep the movement controlled. If you train one arm at a time, budget for both sides.
- 36–45 minutes · B1 curl + B2 pushdown. Two rounds on one adjustable cable with a rope. Curl from the low setting, move the pulley high and push down. Take the time you need for the change, then about 60–90 seconds after the pushdown. If moving the pulley interrupts someone else’s set, use dumbbell curls and a familiar dumbbell triceps extension in the free-weight area instead.
Which exercises should stay apart?
In this session, keep flat bench and incline press apart. If triceps fatigue from the first press ends your next set early, pairing them has made it harder to do the pressing work you came for. Compare reps at your usual load and effort. If your second round falls below your planned range, add recovery before the next round or separate the lifts.
A 2025 systematic review found that supersets generally shortened sessions and felt harder. Across the included studies, average strength and muscle-size outcomes were similar to traditional sets. That finding supports pairing exercises as an option. It does not establish an ideal rest period for this particular bench setup. Read the review by Zhang and colleagues.
What if I only have 35 minutes after waiting?
Finish the bench and pulling work you prioritised. If both arm exercises matter to you today, do one round of each and log the change. If side delts are your priority, keep both lateral-raise sets and leave the arm work for another session. There is no need to rush a heavy set to make the spreadsheet look complete.
How should I log the supersets?
Record each lift on its own line. For example, write “incline DB press, 10 and 9 reps, about 2 RIR” and “chest-supported DB row, 10 and 10, about 2 RIR”. Mark the pair and bench angle so you can reproduce the setup. If you normally use a machine row, start a separate log for this dumbbell version. The next time the gym is quiet, you can go straight back to your usual Upper A.
Want a log for the rest of the week? Preview the training sheet in the paid THG Upper/Lower programme to see how working sets and next-session loads are recorded across the two eight-week blocks.
